KEMPEROL 2K-PUR is a two-component, UV-stable high performance seamless and self-terminating cold fluid-applied polyester reinforced solvent-free. KEMPEROL 2K-PUR Speedshot combined with KEMPEROL 2K-PUR is the ideal solution for all applications where speed is essential. These include balconies. KEMPEROL® 2K-PUR is a solvent-free and odourless, fully reinforced, polyurethane resin-based liquid waterproofing system. It is ideal for use on sustainablility.
|Published (Last):||15 September 2007|
|PDF File Size:||17.90 Mb|
|ePub File Size:||4.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sign in Create account. Flashing our consists of a fully saturated membrane bottom layer looped into the joint as a cradle, a compressible foam or rubber insert at 25 percent compression fitted into the joint, and a membrane top layer applied over the joint. Place the boards onto the roofing adhesive beads. Two-component, solvent-free polyurethane resin for use in improving adhesion of membrane to wood, metal and bituminous substrate surfaces.
Kemperol Reinforcement Foil Reinforcement Strip.
Follow cap sheet manufacturer’s recommendations for the appropriate application procedure. Immediately de-aerate the coating in a cross direction with a porcupine spiked roller in order to release the air bubbles that may develop within the coating.
Ejot Srbija -specijalista u tehnologiji povezivanja. KEMPEROL 2K PUR
All located deficiencies shall be repaired and followed by a re-inspection by the membrane manufacturer. This is my business and I want to improve my profile. Metal flashing flanges to which membrane is to be bonded shall be a minimum of 4 inches in width, and secured to the substrate or wood nailers 6 inches on center staggered with fasteners appropriate to the substrate type. Store products in manufacturer’s kemlerol packaging with labels intact until ready for installation.
Site clean-up, including kempeol interior and exterior building areas that have been affected by construction, shall be restored to preconstruction condition. Reference FM approvals for fastening patterns to satisfy FM wind uplift requirements.
KEMPEROL 2K PUR
Verify substrate surface slopes to drain for horizontal waterproofing applications. Walk on the boards to spread the roofing adhesive for maximum contact.
Movement of materials and equipment across installed membrane is not acceptable. A technical consultant from will be in touch soon.
Work wet membrane with a brush or roller to eliminate blisters, openings, or lifting at corners, junctions, and transitions.
Note that this is a cold applied system and hot asphalt attachment is not acceptable with ;ur insulation and cover boards. Tensile bond strength of membrane to substrate must be greater than or equal to psi 1. Test shall be scheduled through the membrane manufacturer a minimum two weeks prior to the test and completed by an approved testing company.
Two part solvent and odour free waterproofing membrane. Embed Get technical help. Delete if not applicable or if specified in other sections of this specification. Manufacturer’s data sheets on each product to be used, including:.
Distance between joints should not exceed 20 linear feet. Prepare a written report of results of successful and unsuccessful inspection testing and submit to Architect within 7 days following each test. Cap sheet shall be overlapped a minimum of 3 inches for side laps and 6 inches for end laps. Concrete and Masonry Substrate Leveling and Patching: Smaller areas shall receive a minimum of 3 tests. Membrane flashings shall be fabricated with primer appropriate for the substrate surface, resin of the same base chemical type as the field membrane, and fleece of the same weight as the field membrane unless specified otherwise.
Review waterproofing system requirements, Drawings, Specifications and other Contract Documents. Blistering of membrane may result from excessive substrate moisture. Where results exceed the maximum acceptable reading contact Membrane Manufacturer for kemperlo.
Kempertec primer, Kemperol 2k fully re-enforced solvent-free waterproofing. Portland cement-based mortar tile adhesive modified with liquid latex additive for improved adhesion and freeze-thaw resistance, as per ANSI A Substrates shall be inspected and repaired as needed to provide a proper surface to receive waterproofing system. Apply sealer at the manufacturer’s specified coverage rate to provide a sealed, maintainable surface finish.
The lightweight nature of the system adds minimal load, making it particularly useful when roof stability is a concern.
Provide personnel with appropriate safety data information and training as it relates to the specific chemical compounds to be utilized. Once the joint is in place the application of the Traffic Surfacing system may start.
Joint and Crack Preparation: Mix only full units, pot life is approximately 10 minutes. In all such cases flash to an intermediate “cool” sleeve.
Solid to drive on: Tape fabric overlaps, and seal butt joints with tape as well. Primer solution should be a uniform color, with no light or dark streaks present. The fleece can only hold so much resin and all excess should be rolled forward to the unsaturated fleece, eliminating ponding or excessive build-up of the resin.